GOST 613-79: Tin Foundry Bronzes. Grades
Standard Information
Standard Number: ГОСТ 613-79
Title: Tin Foundry Bronzes. Grades
Replaced Standard: ГОСТ 613-65
Implementation Date: January 1, 1980
Classification Code: ОКП 17 3620
Approved by: Decree of the State Committee of the USSR for Standards dated April 26, 1979 No. 1555
International Compliance: Complies with CMEA recommendation РС 1586-75
Table of Contents
1. Scope
This standard applies to tin foundry bronzes intended for the manufacture of castings.
The standard fully complies with the CMEA standardization recommendation РС 1586-75.
2. Grades and Chemical Composition
The grades and chemical composition of tin bronzes for castings shall comply with the requirements specified in the table.
Chemical Composition Table (mass fraction, %)
| Grade | Tin Sn | Zinc Zn | Lead Pb | Phosphorus P | Nickel Ni | Copper Cu | Total Impurities Σ |
|---|---|---|---|---|---|---|---|
| БрОЗЦ12С5 | 2.0-3.5 | 8.0-15.0 | 3.0-6.0 | - | - | Remainder | 1.3 |
| БрОЗЦ7С5Н1 | 2.5-4.0 | 6.0-9.5 | 3.0-6.0 | - | 0.5-2.0 | Remainder | 1.3 |
| БрО4Ц7С5 | 3.0-5.0 | 6.0-9.0 | 4.0-7.0 | - | - | Remainder | 1.3 |
| БрО4Ц4С17 | 3.5-5.5 | 2.0-6.0 | 14.0-20.0 | - | - | Remainder | 1.3 |
| БрО5Ц5С5 | 4.0-6.0 | 4.0-6.0 | 4.0-6.0 | - | - | Remainder | 1.3 |
| БрО5С25 | 4.0-6.0 | - | 23.0-26.0 | - | - | Remainder | 1.2 |
| БрОбЦбСЗ | 5.0-7.0 | 5.0-7.0 | 2.0-4.0 | - | - | Remainder | 1.3 |
| БрО8Ц4 | 7.0-9.0 | 4.0-6.0 | - | - | - | Remainder | 1.0 |
| БрО10Ф1 | 9.0-11.0 | - | - | 0.4-1.1 | - | Remainder | 1.0 |
| БрО10Ц2 | 9.0-11.0 | 1.0-3.0 | - | - | - | Remainder | 1.0 |
| БрО1ОС10 | 9.0-11.0 | - | 8.0-11.0 | - | - | Remainder | 0.9 |
3. Notes
Note 1: In bronzes of grades БрОЗЦ7С5Н1, БрОЗЦ12С5, БрО8Ц4 and БрО10Ц2, the total content of silicon and aluminum impurities shall not exceed 0.02%.
For castings not intended for parts operating under hydraulic pressure, by agreement between the manufacturer and the consumer, the aluminum content may be increased to 0.05% and the silicon content to 0.05%.
Note 2: Impurities of arsenic up to 0.15%, magnesium up to 0.02%, sulfur up to 0.05% are allowed, all included in the total impurity content.
Note 3: Except for grade БрОЗЦ7С5Н1, the mass fraction of nickel in all grades may be increased to 2.0% (deducted from the copper content, not included in the total impurity content).
Note 4: By agreement between the manufacturer and the consumer, the mass fraction of lead in bronzes of grades БрО10Ц2 and БрО8Ц4 may be increased to 1.5% (not included in the total impurity content).
Note 5: In castings from bronzes of grades БрО10Ц2 and БрО8Ц4 intended for welded structures, the mass fraction of lead shall not exceed 0.05%.
Note 6: By agreement between the manufacturer and the consumer, the mass fraction of phosphorus in grade БрО1ОС10 may be increased to 1.0%.
Note 7: Impurities not specified in this standard are included in the total impurity content.
4. Mechanical Properties
The mechanical properties of unheat-treated bronzes and their applications are given in Appendix 1.
5. Test Methods
5.1 Chemical Composition Analysis
The chemical composition of bronzes is determined according to GOST 1953.1-79 — GOST 1953.12-79, GOST 25086-87.
5.2 Mechanical Properties Determination
Tensile strength and elongation after fracture are determined in accordance with standard technical documentation.
5.3 Tensile Test
Tensile tests are carried out in accordance with GOST 1497-84.
5.4 Brinell Hardness Test
Brinell hardness is determined in accordance with GOST 9012-59.
5.5 Standard Correspondence
The correspondence between the grades of tin bronzes of this standard and GOST 613-65 is given in Appendix 2.
Appendix 1: Reference Data
Mechanical Properties and Applications of Tin Bronzes
Note: Designation of casting methods: к — chill casting; п — sand casting.
| Grade | Casting Method | Tensile Strength σв MPa (kgf/mm²) | Elongation δ % | Brinell Hardness HB MPa (kgf/mm²) | Applications |
|---|---|---|---|---|---|
| БрОЗЦ12С5 | к | 206 (21) | 5 | 588 (60) | General purpose fittings |
| п | 176.2 (18) | 8 | 588 (60) | ||
| БрОЗЦ7С5Н1 | к | 206 (21) | 5 | 588 (60) | Parts operating in oil, steam and water |
| п | 176.2 (18) | 8 | 588 (60) | ||
| БрО4Ц4С17 | к | 147 (15) | 12 | 588 (60) | Anti-friction parts |
| п | 147 (15) | 5 | 588 (60) | ||
| БрО5Ц5С5 | к | 176.2 (18) | 4 | 588 (60) | Fittings, anti-friction parts, bearing bushes |
| п | 147 (15) | 6 | 588 (60) | ||
| БрО5С25 | к | 137.2 (14) | 6 | 588 (60) | Bimetallic sliding bearings |
| п | 147 (15) | 5 | 441 (45) | ||
| БрОбЦбСЗ | к | 176.2 (18) | 4 | 588 (60) | Fittings, anti-friction parts, bearing bushes |
| п | 147 (15) | 6 | 588 (60) | ||
| БрО8Ц4 | к | 196 (20) | 10 | 735 (75) | Fittings, pipe fittings, pumps operating in seawater |
| п | 196 (20) | 10 | 735 (75) | ||
| БрО10Ф1 | к | 245 (25) | 3 | 882 (90) | Fitting friction pairs, high-loaded parts of screw drives, clamping and spindle nuts, worm wheel rims |
| п | 215.5 (22) | 3 | 784 (80) | ||
| БрО10Ц2 | к | 225.5 (23) | 10 | 735 (75) | Fittings, anti-friction parts, bearing bushes, friction parts and crankshaft liners |
| п | 215.5 (22) | 10 | 637 (65) | ||
| БрО1ОС10 | к | 196 (20) | 6 | 735 (78) | Sliding bearings operating under conditions of high specific pressures |
| п | 176.2 (18) | 7 | 637 (65) |
Appendix 2: Correspondence Between Old and New Standard Grades
Correspondence between grades of GOST 613-79 and GOST 613-65
| Grade of GOST 613-79 | Grade of GOST 613-65 |
|---|---|
| БрОЗЦ7С5Н1 | БрОЦСНЗ-7-5-1 |
| БрОЗЦ12С5 | БрОЦСЗ-12-5 |
| БрОбЦбСЗ | - |
| БрО8Ц4 | - |
| БрО4Ц7С5 | БрОЦСЗ,5-7-5 |
| БрО10Ф1 | - |
| БрО4Ц4С17 | БрОЦС4-4-17 |
| БрО5Ц5С5 | БрОЦС5-5-6 |
| БрО10Ц2 | - |
| БрО1ОС10 | - |
| БрО5С25 | - |
Important Notes
- Standard Status: This is NOT the official version, reference only
- Technical Support: For technical consultation, contact relevant standardization bodies
- Version Update: This standard replaces the previous GOST 613-65 version
- International Correspondence: Complies with CMEA standardization recommendation РС 1586-75
Translation of GOST 613-79 | Last updated: December 23, 2025
All Russian grade designations are preserved as specified in the original standard
Correction: Added sand casting (п) data for БрОЗЦ7С5Н1 grade
